【動作品】Broadcom Brocade VDX-6720 10G L2スイッチ
メーカー：Boadcom
機種：Brocade VDX 6720 10GL2スイッチ(前方吸気後方排気モデル)
状態：
１１月末まで我が家で利用していた機器です。機器の更新に伴い不要となったので出品します。
以下起動ログを記載しておきます。
設定の初期化済みですので、ログインID/PWはadmin/passwordとなります。
ーーー以下起動ログーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
The system is coming up, please wait...
U-Boot 2010.06 (Nov 24 2015 - 11:33:27)
CPU: 8548, Version: 2.1, (0x80310021)
Core: E500, Version: 2.2, (0x80210022)
Clock Configuration:
CPU0:1200 MHz,
CCB:400 MHz,
DDR:200 MHz (400 MT/s data rate), LBC:50 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Model ID: 0x804b
Board: 8548 CALLISTOE
I2C: ready
DRAM: Initializing....
DDR: 2 GiB (DDR2, 64-bit, CL=3, ECC on)
POST RAM test disabled.
Now running in RAM - U-Boot at: 7ffa0000
FLASH: 4 MiB
L2: 512 KB enabled
CPLD: Init complete
ATA interface setup upm 256: ffdfc04, fffffc01, fffffc00, fffffc00
PCI: gd->brcd_flags = 0, PCI init
PCI1 connected to Slot 1 as host (base addr f7008000)
Scanning PCI bus 00
00 11 1657 0010 0280 1a
00 14 1131 1561 0c03 1a
00 14 1131 1562 0c03 1a
PCIE1 on bus 00 - 00
PCIE3 connected to Slot 3 as Root Complex (base addr f700a000)
Scanning PCI bus 02
04 00 1657 001a 0280 3c
03 01 10b5 8618 0604 1a
05 00 1657 001a 0280 3d
03 02 10b5 8618 0604 1a
06 00 1657 001a 0280 3e
03 03 10b5 8618 0604 1a
07 00 1657 001a 0280 3f
03 05 10b5 8618 0604 1a
08 00 1657 001a 0280 40
03 07 10b5 8618 0604 1a
09 00 1657 001a 0280 41
03 09 10b5 8618 0604 1a
0a 00 1657 001a 0280 42
03 0a 10b5 8618 0604 1a
0b 00 1657 001a 0280 43
03 0b 10b5 8618 0604 1a
0c 00 1657 001a 0280 44
03 0c 10b5 8618 0604 1a
03 0d 10b5 8618 0604 1a
03 0e 10b5 8618 0604 1a
03 0f 10b5 8618 0604 1a
02 00 10b5 8618 0604 1a
PCIE1 on bus 01 - 0f
In: serial
Out: serial
Err: serial
Net: eTSEC0, eTSEC1
set_bootstatus: BS_LOAD_OS, platform_index = 2
Hit ESC to stop autoboot: 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Map file at LBA sector 0x30c03f
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Linux-2.6.34.6
Image Type: PowerPC Linux Multi-File Image (gzip compressed)
Data Size: 3499952 Bytes = 3.3 MiB
Load Address: 00000000
Entry Point: 00000000
Contents:
Image 0: 2376858 Bytes = 2.3 MiB
Image 1: 1072386 Bytes = 1 MiB
Image 2: 4581 Bytes = 4.5 KiB
Image 3: 4152 Bytes = 4.1 KiB
Image 4: 4581 Bytes = 4.5 KiB
Image 5: 4143 Bytes = 4 KiB
Image 6: 5160 Bytes = 5 KiB
Image 7: 3917 Bytes = 3.8 KiB
Image 8: 4580 Bytes = 4.5 KiB
Image 9: 4580 Bytes = 4.5 KiB
Image 10: 4580 Bytes = 4.5 KiB
Image 11: 5194 Bytes = 5.1 KiB
Image 12: 5168 Bytes = 5 KiB
Verifying Checksum ... OK
## Loading init Ramdisk from multi component Legacy Image at 02000000 ...
## Flattened Device Tree from multi component Image at 02000000
Booting using the fdt at 0x2352d90
Uncompressing Multi-File Image ... OK
Loading Ramdisk to 1fefa000, end 1ffffd02 ... OK
Loading Device Tree to 01ffb000, end 01fff1e3 ... OK
this is quiet!
endof DRAM 2147483648 memstart_addr0 total_lowmem -2147483648
setup_arch: bootmem
mpc85xx_setup_arch()
arch: exit
SLUB: dfree enabled
PRIMING SLUB: main caches
SLUB: export __kmalloc at 0x400e590c changed to 0x400e5c68
SLUB: export vmalloc at 0x400d4958 changed to 0x400d4808
SLUB: export vfree at 0x400d3170 changed to 0x400d30ec
network namespace NR故障品(垃圾品)、問題商品、可能無法修理,請注意 (VRF) started
mmod_sysctl_inited: 1
Unable to fetch uboot wdt count
Installing Linux 2.6 Kernel
Attempting to find a root file system on hda1...
INIT: version 2.78 booting
Firmware Integrity Check is default off
Bypassing firmware validation.
--769--0x0301--3 1--0x0301--
--769--0x0301--3 2--0x0302--
Hostname is sw0INIT: Entering runlevel: 3
FIPS-mode test application
1. Non-Approved cryptographic operation test...
a. Excluded algorithm (MD5)...successful
b. Included algorithm (D-H)...successful
2. Automatic power-up self test...successful
3. AES-128,192,256 CBC encryption/decryption...successful
4. RSA key generation and encryption/decryption...successful
4.1. RSA 2048 with 'SHA256' testing...successful
5. TDES-CBC encryption/decryption...successful
6a. SHA-1 hash...successful
6b. SHA-256 hash...successful
6c. SHA-512 hash...successful
6d. HMAC-SHA-1 hash...successful
6e. HMAC-SHA-224 hash...successful
6f. HMAC-SHA-256 hash...successful
6g. HMAC-SHA-384 hash...successful
6h. HMAC-SHA-512 hash...successful
7. Non-Approved cryptographic operation test...
a. Excluded algorithm (MD5)...Not executed
b. Included algorithm (D-H)...successful as expected
8. Zero-ization...Successful
9. TLS KDF...successful
10. SSH KDF...successful
All tests completed with 0 errors
Cannot get current device settings: No such device
not setting speed
not setting duplex
not setting autoneg
(none)
Waiting to starting configuration management service
Starting configuration management service
Found 1(threshold 5) abnormal reboots within 7200 seconds window(threshold)
KernelSpace rastrace_register
SWBD module launch ... Fri Dec 31 10:02:00 JST 1999
callisto: setting to MASTER as HA bit is not set
eAnvil rev B found
Info: panic dump has been initialized!
Creating L3-L2 fifo Fri Dec 31 10:02:42 JST 1999 ...
Starting HASM ... Fri Dec 31 10:02:43 JST 1999
/etc/rc.d/rc3.d/S95fabos: silicond: command not found
Exisitng reboot reason fsize = 5 rb=
The file contains no trace dump information.
Network OS (sw0)
sw0 console login: Starting Dcmd ... Fri Dec 31 10:02:48 JST 1999
server starting
Restoring DCM databasetp_register, got none fss tp handle=10000001h
1999/12/31-10:02:52, [HASM-1004], 35991,, INFO, VDX6720-60, Processor reloaded - Reset.
...done
waiting for server to shut down....................... done
server stopped
Fri Dec 31 10:09:03 JST 1999 :: Confd: Waiting for Dcmd to become ready...
CHASSIS RECOV_ACTIVE
SNMP Research EMANATE/Lite Agent Version 16.2.0.9
Copyright 1989-2006 SNMP Research, Inc.
Confd: No need to wait for Ccmd...
Fri Dec 31 10:09:21 JST 1999 :: Triggering confd load phase1 after waiting for 10 secs
Warn: imi_debug :zg->protocol is not set before lib_start()
Critical FDB init success
pcap_master_init - sm is NULL after ha_calloc
1999/12/31-10:09:44, [BGP-1002], 35992,, INFO, sw0, BGP: Daemon ready for action
.
nsm_client_start - ret = 0
NOS : Initialize DY-SYNC LIB : mgmt_state 34002110
NOS : Init bc_pkt 1024dc3c bc_index 20 ***
***********************************************************
hal_new_link_cb: NSM: initialized system SVI mac: 00:27:f8:29:1f:d2
************************************************************
1999/12/31-10:09:57, [MFIC-1002], 35993,, INFO, sw0, Chassis FRU header not programmed for switch NID, using defaults (applies only to FICON environments).
1999/12/31-10:10:01, [SEC-1197], 35994,, INFO, VDX6720-60, Changed account admin.
1999/12/31-10:10:02, [SEC-1197], 35995,, INFO, VDX6720-60, Changed account user.
1999/12/31-10:10:13, [ZONE-1046], 35996,, INFO, sw0, The Default Zone access mode is already set to All Access.
Updating flash ...
All service instances on Active
1999/12/31-10:10:13, [ZONE-1024], 35997,, INFO, sw0, cfgSave completes successfully.
.
1999/12/31-10:10:13, [HASM-1108], 35998,, INFO, VDX6720-60, All service instances become active.
1999/12/31-10:10:13, [DOT1-1013], 35999, DCE, INFO, sw0, DOT1X test timeout value is set to 10.
1999/12/31-10:10:13, [DCM-1002], 36000,, INFO, VDX6720-60, PostBoot processing on global config has started.
1999/12/31-10:10:14, [ONMD-1002], 36001, DCE, INFO, sw0, LLDP global configuration is changed.
1999/12/31-10:10:14, [ONMD-1002], 36002, DCE, INFO, sw0, LLDP global configuration is changed.
DCE Blade: Callisto board version 4
POST1: started running Fri Dec 31 10:10:17 JST 1999
1999/12/31-10:10:17, [RAS-2001], 36003,, INFO, sw0, Audit message log is enabled.
1999/12/31-10Enabling Eth switch... 1
:10:18, [RAS-2003], 36004,, INFO, sw0, Audit message class configuration has been changed to CONFIGURATION,FIRMWARE,SECURITY.
1999/12/31-10:10:18, [HASM-1108], 36005,, INFO, VDX6720-60, All service instances become active.
POST1: Test #1 - Running Turboramtest
1999/12/31-10:10:18, [ONMD-1002], 36006, DCE, INFO, sw0, LLDP global configuration is changed.
1999/12/31-10:10:18, [ONMD-1002], 36007, DCE, INFO, sw0, LLDP global configuration is changed.
1999/12/31-10:10:19, [NSM-2014], 36008, DCE, INFO, sw0, VLAN sub-profile for port-profile UpgradedVlanProfile is created.
1999/12/31-10:10:19, [NSM-2017], 36009, DCE, INFO, sw0, Port-profile UpgradedVlanProfile is configured for switching properties.
1999/12/31-10:10:19, [NSM-2019], 36010, DCE, INFO, sw0, The trunk mode is configured for port-profile UpgradedVlanProfile.
1999/12/31-10:10:19, [NSM-2024], 36011, DCE, INFO, sw0, All VLANs are configured as tagged VLANs for port-profile UpgradedVlanProfile.
1999/12/31-10:10:19, [NSM-2044], 36012, DCE, INFO, sw0, Domain: default creation successful.
1999/12/31-10:10:19, [NSM-2046], 36013, DCE, INFO, sw0, Profile: UpgradedVlanProfile addition to domain default successful.
1999/12/31-10:10:19, [RTM-1023], 36014, DCE, INFO, sw0, Route 0.0.0.0/0 pointing to management interface will not be redistributed to other protocols.
.
1999/12/31-10:10:20, [DCM-1003], 36015,, INFO, VDX6720-60, PostBoot processing on global config is complete.
POST1: Test #2 - Running Diagshow
POST1: Script PASSED with exit status of 0 Fri Dec 31 10:10:27 JST 1999 took (0:0:10)
POST2: started running Fri Dec 31 10:10:31 JST 1999
POST2: Test #1 - Running portloopbacktest -lb_mode 2
POST2: Test - Skipping portloopbacktest -lb_mode 8
POST2: Script PASSED with exit status of 0 Fri Dec 31 10:11:00 JST 1999 took (0:0:29)
1999/12/31-10:11:14, [BL-1000], 36016,, INFO, VDX6720-60, Initializing ports...
1999/12/31-10:11:17, [BL-1034], 36017,, INFO, VDX6720-60, SWITCH CEE initialization completed.
Set VLP module index 0 to module 0
sys_init: before msg_init1
init_dy_sync_slave(), sync_type = 49 >= 49
module_slot_pre_init: setting module # 0 fid_base to: 1774
link is up
1999/12/31-10:11:28, [DCM-1002], 36018,, INFO, VDX6720-60, PostBoot processing on L0 config has started.
1999/12/31-10:11:33, [HASM-1111], 36019,, INFO, VDX6720-60, Configuration replay has completed on SWITCH.
1999/12/31-10:11:33, [DCM-1003], 36020,, INFO, VDX6720-60, PostBoot processing on L0 config is complete.
1999/12/31-10:11:33, [DCM-1007], 36021,, INFO, VDX6720-60, No Configuration File Replay.
1999/12/31-10:11:33, [DCM-1005], 36022,, INFO, VDX6720-60, Configuration Replay is complete.
1999/12/31-10:11:33, [SEC-1334], 36023,, INFO, VDX6720-60, local security policy not saved.
1999/12/31-10:11:33, [SEC-1334], 36024,, INFO, VDX6720-60, local security policy not saved.
1999/12/31-10:11:33, [HASM-1110], 36025,, INFO, VDX6720-60, Configuration replay has completed on the system.
1999/12/31-10:11:33, [DCM-1116], 36026,, INFO, VDX6720-60, System initialization is complete. NOS is ready to handle all commands.
1999/12/31-10:11:36, [SEC-1197], 36027,, INFO, VDX6720-60, Changed account admin.
1999/12/31-10:11:36, [SEC-1197], 36028,, INFO, VDX6720-60, Changed account user.
Network OS (sw0)
sw0 console login: admin
Password:
WARNING: The default password of 'admin' and 'user' accounts have not been changed.
Welcome to the Brocade Network Operating System Software
admin connected from 127.0.0.1 using console on sw0
sw0#
sw0#
sw0#
sw0#
ーーーここまでーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーーー
好評 (86)
差評 (1)
